Comes standard with the following:

• New & improved EZE CHANGE™ Profile system (complete changeover in 30 minutes or less)
• Hydraulic Drive and Shear
• Quick Change Power Pac™ wiht 16 HP Electric Start Gasoline Engine or 7.5 HP 220V Three Phase Motor
• Two Sets of Bead, Pencil, or V-Rib Rollers
• Forms 30 - 24 ga. Steel, .019 - .040 Aluminum, 16 oz. - 20 oz. 3/4 Hard copper with coils up to 24 inches wide
• Optionial Computer Batch and Length Control with Panel Recognition Photo Eye
• Approximately 60 feet per Minute Panel Speed
• Limited 3 Year Parts/ 1 Year Labor
• Limited Lifetime Separation on Drive Rollers
• Limited Lifetime on Stainless Steel Forming Rollers

• Runs Steel from 24 to 30 gauge
• Runs Copper, Aluminum, Steel
• Snap-lock, Mechanical Seam, T Panel, ARMCO style and Bermuda Profiles
• Clip Relief and/or Stiffening can be added to any Panel Profile Striated Paneling Rollers also available
• Separate drive and form rollers eliminates most oil canning

  This means better products, less problems, and lower costs.

Panformer

Length - 12' (3.657m)

Width - 4"5" (1.346m) plus engine projection

Height - 1'3" (.381m) plus engine projection

Weight - 2010 lbs. (912kg)

Features

The Standing Seam Power Panel machine makes various standing seam roof pans in any width from 12" - 24", depending on the panel configuration. It will accept coil widths from 16" to 28". The machine is complete with a hydraulic drive system and cast polyurethane drive rollers, 16 H.P. electric start gasoline engine, hydraulic shear that cuts any width panel, remote limit switch, 2 sets of bead rollers, and a single remote decoiler stand. It requires a forming roller system to produce panels. Prewiring for later addition of sealant pump system is included.

Panformer on Trailer

Length - 17'2" (5.232m)

Width - 7'3" (2.21m)

Height - 6'3" (1.905m) with reel

Weight - 3990 lbs (1810kg)

Stainless steel forming roller systems on mounting bars are available as follows:

SS100 Makes 1" high x .5" wide mechanically seamed panel leg

SS150 Makes 1.5" high x .5" wide mechanically seamed panel leg

A hand seamer comes with each of the above systems.

Power

16 H.P. Electric Start Gas Engine

SS550 Makes 1.5" h x 7/17" wide SNAP-LOCK I snap seam panel. The most positive engagement available.

Drive

hydraulically powered chain driven cast polyurethane drive rollers

SS675 Makes 1.75" high x 7/16" wide SNAP-LOCK II snap seam panel.

Shear

Electrically activated, hydraulically powered, infinitely adjustable full cycle with safety interlock/stop

FF100 Roller system to make 1" high snap lock seamed panel with slotted nailer leg for clipless installation.

BP Roller System on mounting bars and cut-off dies to make Horizontal Bermuda Panels. Panels can have a or 1.5" bottom edge and have 11.5" or wider exposure.

Speed

Approximately 75ft/min. Speed should be decreased 25-50% when using sealant pump depending on temperature

Available Options

TA12 12,000# capacity tandem axle trailer. Has dual reel overhead decoiler standard. No remote decoiler will be furnished.

Materials Formed

Steel - 30 - 24 gauge (painted, galvanized)

Aluminum .019 to .040

Copper 16 oz. to 20 oz.

SSH

Standing Seam Panel machine (as or Electric) Includes hydraulic drive and hydraulic shear, computer assembly, bead roller assembly, and one profile roller set.

$26,950

SS100

Roller system on mounting bars and cut-off dies for 1" high x 1/2 " wide mechanically seamed panel. Includes hand seamer

$4,950 **$2860

SS150

Roller system on mounting bars and cut-off dies for 1.5" high x 1/2 " wide mechanically seamed panel. Includes hand seamer

$5,250 **$3,155

SS450

1 1/2" high x 1/4" wide SNAP LOCK CLIP snap seam panel

$6,265 **$4,175

SS550

Roller system on mounting bars and cut-off dies for 1.5" high x 1/2 " wide SNAP LOCK I snap seam panel.

$7,565

SS675

Roller system on mounting bars and cut-off dies for 1.75" high x 1/2 " wide SNAP LOCK II snap seam panel.

$9,895

FF100

1" high snap seam with slotted flange for clipless installation.

Includes Clip Relief Rollers

$7,320

BP

Roller system on mounting bars and cut-off dies to make Bermuda Panels. Panels can have 1" or 1.5" bottom edge and have 11.5" or wider exposure.

$8,730

**$6,640

CR

Clip relief rollers - When added to SS150, SS550, or SS675

$170

** SS100, SS150, SS450 and BP Roller Systems all use identical left side roller sets. If you purchase or own one of these roller systems, you can add any of the other three systems at a reduced price.

OPTIONS AVAILABLE

TA12

12,000# capacity tandem axle trailer with crane eyes for lifting.

(Note: Reel rack and reels or expandable arbors sold separately)

$5250

DR1

Machine Mount Dual Overhead Decoiler

$940

ROS10

10' of variable height runout stands

$240

HS1

Hand seamer for use with SS100 & SS150 mechanically seamed panels

$180

HS2

Hand Seamer for use with SS200 mechanically seamed panels.

$365

RR1

Additional Bead Roller - per pair

$300

RR2

Pencil Rib Rollers (large) - per set

$300

RR3

V-Rib Rollers (large) - per set

$300

RR4

Pencil Rib Rollers (small) - per set

$300

RR5

V-Rib Rollers (small) - per set

$300

RR6

Striation Rollers - peer pair (4 pairs required per machine

$300

RRF

Additional Frame Assembly for mounting RR1, RR2, RR3, RR4, RR5 & RR6

$300

DRCO1

Dual register electronic control - panel length and quanity

$3,755

DR01

Decoiler reels (16" or 20")

$380

EXA

Expandable Arbor Decoiler Reel 16" to 20" diameter

$820

CRTP

Panel Machine Crate

$695